Product Description
Rane Terminal 1010x audio dsp multiprocessor
The Terminal 1010x takes the DSP Experience to the next level with an intuitive front-panel that enables users to control 10 analog balanced inputs for Mic/Line/+48V and 10 balanced outputs. There are also 6 flexible RAD Plus PoE ports to connect breakout boxes and wall plate remote controls and 4 Universal GPIO logic ports for external devices such as alarm systems, sensors, lights, projectors, etc. There is also a slot for an optional DANTE™ 32x32 card for network connectivity.
Features
- - Native Analog 10-in/10-out
- - 6 RAD+ Ports support RADs and DRs - adds 12-in/12-out, for a total 22-in/22-out
- - Optional DANTE™ card adds 32-in/32-out on the network
- - Expansion Port for future hardware releases
- - Online Wizard for quick-start using Halogen software
- - Enhanced front panel control and monitoring
Technical Specifications
| Analog I/O | Type | 10 in x 10 out | |
| ADC | High definition audio 24-bit, 48kHz, DR 116dB A-weighted | ||
| DAC | High definition audio 24-bit, 48kHz, DR 116dB A-weighted | ||
| Frequency Response | 20Hz–20kHz, ±0.1dB | ||
| Inputs | Connection | (5) Euroblock connectors, 6 pins each, 3.81mm pitch, green. Ships with strain relief plugs. | |
| Condenser Mic Mode | Type | Active balanced, microphone input mode with 48V phantom power | |
| Phantom Power | +48V | ||
| Maximum Input | 1Vrms | ||
| Input Impedance | 2.5kΩ | Each leg | |
| Dynamic Mic Mode | Type | Active balanced, microphone input mode without phantom power | |
| Maximum Input | 250mVrms | ||
| Input Impedance | 2.5kΩ | Each leg | |
| Line Mode | Type | Active balanced, line-level | |
| Maximum Input | 8Vrms | ||
| Input Impedance | 5kΩ | Each leg | |
| Line+ Mode | Type | Active, left [+] & right [-] signals summed to mono | |
| Maximum Input | 8Vrms | ||
| Input Impedance | 5kΩ | Each leg | |
| Outputs | Connection | (5) Euroblock connectors, 6 pins each, 3.81mm pitch, orange. Ships with strain relief plugs. | |
| Type | Active balanced, line output mode with active output transient muting | ||
| Maximum Output | 8Vrms | ||
| Impedance | 300Ω | Each leg | |
| Frequency Response | 20Hz–20kHz, ±0.1dB | ||
| DSP | Processing Power | >10,000 MIPS | |
| Word Length | 32-/64-bit Floating Point | ||
| Delay Memory | Min. 160sec total | ||
| Computer Interface | Type | Ethernet 1000 base-T | Zeroconf service discovery protocol for easy setup |
| Connection | RJ-45 | Shielded Cat 5e cable or better | |
| Length | 300ft./100m | Standard Ethernet cable length limit | |
| RAD+ Ports | Connection | (6) RJ-45 | Shielded Cat 5e cable or better |
| Audio Channels | 2 in, 2 out | Each port, control channel 24-bit, 48kHz | |
| Voltage | 27 VDC | Each port | |
| Power | 12W (peak)/6W (average) | Each port | |
| Length | DR devices: 984ft./300m | RAD devices: 325ft./100m | |
| Universal Logic I/O | Connection | (1) mini-Euroblock connector, 6 pins, 3.81mm pitch, black | |
| Logic In | Internal Pull-Up | 5mA | Protected to +24V, reverse-polarity-protected |
| Vin High | > 2.2V | Normal state | |
| Vin Low | < 1.0V | ||
| Logic Out | Open Collector Output | Source 5mA, Sink 200mA | Protected to +24V, reverse-polarity-protected |
| Vout High | > 2.2V | ||
| Vout Low | < 0.2V | ||
| Ratiometric Input | Input | 0–5V | |
| V+ | 40mA | ||
| Resolution | 8-bit at 2kHz sample rate | ||
| Expansion Port | Types | Rane Expansion Bus | 512 x 512, 48kHz digital audio plus control. Up to 32 Halogen Expansion Devices |
| Dante card (optional) | 32 x 32 with sample-rate conversion, allowing 96kHz sample rate Dante flows | ||
| Connection | RJ-45 | Shielded Cat 5e cable or better | |
| Maximum Length | 300ft./100m | ||
| Power | Connection | IEC | |
| Voltage | 90–260VAC, 50/60Hz | ||
| Consumption | 70W | ||
| Output | 28V | ||
| Unit | Wiring | Class 2 | Rear-panel terminals |
| Operating Temperature | 32–104°F, 0–40°C | ||
| Fan | 10CFM, low noise (<20dBa), long life (60k hours at 45°C) | ||
| Dimensions | 19.0" x 8.25" x 1.73" 48.3cm x 20.9cm x 4.4cm |
Width x depth x height | |
| Weight | 7.0 lbs., 3.2 kg | ||
Package Contents
- - Terminal 1010x
- - (5) 6-pin 3.8 mm Euroblock input (green, for audio inputs)
- - (5) 6-pin 3.8 mm Euroblock outputs (orange, for zone outputs)
- - (1) 6-pin 3.8 mm Euroblock input (black, for logic input)
- - IEC Power Cable
- - Quickstart Guide
- - Safety & Warranty Manual
