Product Description
ETC UFR2-LV Unison Foundry Dual-Zone DMX Relay With 0-10V
The ETC UFR2-LV Unison Foundry 0-10V Dimming Controller offers DMX controlled, fully-rated 20-Amp relays with fully isolated 0-10V dimming for direct control of compatible LED drivers and fluorescent dimming ballasts. This style of dimming controller can be mounted to electrical junction boxes.
The UFR2-LV Controller provides two outputs of control that can be wired to individual fixtures or used for zone control. Each output can be configured to a separate DMX address, or both outputs can be controlled in unison by setting the 0–10V Controller to single-channel mode. This model allows you to control connected loads from any DMX control device. Configure the 0–10V Controller either remotely via RDM (using a tool like ETC Net3 Concert) or locally on the controller.
Features:
- Switched power control of two circuits with 0-10V dimming
- 20A fully-rated relays for use with general purpose, tungsten, fluorescent and LED loads
- Supports plug loads
- 120/277VAC power input
- DMX controlled and RDM configurable
Specifications:
- Ambient Environment:
- For indoor use only.
- Rated for plenum use.
- 32°F to 104°F (0°C to 40°C) operating temperatures in 5–95% non-condensing humidity.
- Electrical Specification:
- The 0-10V Controller Supports:
- Power input 120–277VAC, 60 Hz
- Maximum load rating is 20A (total connected load)
- NOTE: The maximum load on the 0-10V Controller can be split between the two relay outputs in any combination required for the installation, but cannot exceed 20A total connected load for the controller.
- Independent control for 0-10V fluorescent ballasts and/or LED drivers, each is capable of sinking 100mA
- Supported Load Types (all voltages):
- 20A fully-rated relay for use with general purpose, tungsten, fluorescent, and LED lighting loads.
- Compliance:
- UL and cUL listed
- Conforms to UL 916 (Energy Management Equipment) and UL 2043 (Plenum rated)
- Physical:
- Size (H x W x D): 2 x 3.5 x 3 in
- Weight: 0.75 lbs
APPLICATIONS • Arena and stadium suites • Office buildings • Conference and meeting rooms • Healthcare facilities • Houses of worship • Classrooms • Hospitality and restaurants • Retail
FEATURES • Switched power control of two circuits with 0-10V dimming • 20A fully-rated relays for use with general purpose, tungsten, fluorescent and LED loads • Supports plug loads • Fully isolated 0-10V dimming outputs • 120/277VAC power input • DMX controlled and RDM configurable
GENERAL • UL and cUL LISTED • Rated for plenum use
FUNCTIONAL • Control for individual fixtures, zone power and 0-10V dimming for fluorescent ballasts and LED drivers • Supports USITT DMX512-A (ANSI E1.11) • Supports RDM (ANSI E1.20)
MECHANICAL • Constructed of injection-molded ABS plastic • Button interface and LED indicators for configuration • Half-inch conduit knockout mounted • Mains-voltage wiring exits through knockout mount • 0-10V dimming control wiring exits through knockout mount • DMX wiring connects to side of controller • Mains power input connections: - 12 AWG Hot - Black - 14 AWG Neutral - White • Relay output connections: - Zone 1, 12 AWG - Red - Zone 2, 12 AWG - Red/White • 0-10V dimming output connections: - Zone 1, 18 AWG - Violet and Gray - Zone 2, 18 AWG - Violet/White and Gray/White • Optional mounting plate available for applications that require low-voltage wiring to be in conduit
ELECTRICAL • 120V-277V, 50/60Hz power input • Normally Open (NO) 20-amp fully-rated relay • Supports lighting and plug loads • 0-10VDC control rated for up to 100mA sink per output - 0-10V connections are fully isolated from ground to 2500V RMS • UL and cUL LISTED - Conforms to UL 508 and UL 2043
DMX INPUT PORT • Optically-isolated from Controller electronics • Withstands fault voltages of up to 250VAC • Integrated DMX/RDM termination
CONFIGURATION • Remote configuration available via RDM controllers including: - ETC DMX/RDM gateway networked to a device running ETC Net3 Concert software - ETC control console with RDM functionality - 3rd party configuration and control products • Manual configuration of the starting DMX address on the controller
THERMAL • Ambient room temperature: 0 to 50°C • Ambient humidity: 5 to 95% non-condensing