Product Description
Doug Fleenor Design GIZMO DMX Tester and Signal Generator
The Gizmo is a DMX512 test tool with features useful for lighting system setup, testing, troubleshooting, and commissioning. With the Gizmo you can transmit, receive, save, playback scenes and perform a variety of data and cable tests. It is housed in a rugged chassis made of 0.1" thick aluminum. A fitted carrying case and wall transformer/battery charger are included with each Gizmo. Direct channel access while sending or receiving DMX512 signals is possible through the use of the numeric keypad. The display is a back lit 16 character by 2 line LCD. The Gizmo has a fully opto-isolated DMX512 input. The DMX512 output can function as an isolated pass-thru which also re-times the signal.
Features
- Transmit Up to 512 Channels of DMX512 - Select individual channels using the channel check mode, or select groups of channels using the AND and THRU buttons. Adjust levels with the Up/Down arrows, or press the AT key followed by the level to set a specific value. Press CLEAR to deselect channels leaving levels unchanged. Use the GIZMO as a stand-alone console for all your DMX emergencies. Even change the start codes if desired.
- Receive DMX512 - Receive and display data in several formats. The operator can view all 512 channel levels, selected levels, non-zero channels, the refresh rate, number of channels transmitted, received start codes, flicker, and pass through mode for troubleshooting problems.
- Save and Recall 100 Scenes - Save and restore snapshots of DMX512 levels. The GIZMO can save and recall up to 100 scenes of either the currently received DMX levels or transmitted data.
- Continuity, Pin Correctness and Data Reliability - Tests check cables for shorts, open connections, and data reliability.
- LCD Display - Two line back light display, visible in the dark or direct sunlight with the low power back light display.
- 9 Volt Battery or AC Power Operation - Uses a typical 9 volt battery or included A/C (wall mount) supply.
- Durable Metal Housing - The .10" aluminum enclosure can withstand on the road travel
- Padded Carry Case Included - Manufactured by REELINE features a layer of closed cell foam to protect against moisture.
- 25 Button Key pad - Full keypad with CLEAR, ENTER, ALL, AND, THRU and TOP buttons.
Specs
Input baud rate: 250 Kb/s
Input circuit: ESD protected EIA-485 transceiver (LT1785)
Input signal: 3 volts minimum, 12 volts maximum
Input connector:
- Male Gold plated 5 pin XLR (Neutrik D-1 series).
- Pin 1 = common, Pin 2 = Data-, Pin 3 = Data+. Cable check on pin 4 and pin 5
Output isolation: 600 Volts
Output baud rate: 250 Kb/s
Output circuit: ESD protected EIA-485 transceiver (LT1785)
Output signal: DMX512-A
Output connector:
- Female Gold plated 5 pin XLR (Neutrik D-1 series).
- Pin 1 = common, Pin 2 = Data-, Pin 3 = Data+ Cable check on pin 4 and pin 5
User interface: 25 button keypad and two line 16 character backlit LCD display
Battery: Provided with 9 Volt NiMH rechargeable or User provided 9 Volt Alkaline (see “Notes On The Battery”)
Wall power supply:
- Input: 100 - 240VAC 0.5A Max. 50/60 Hz
- Output: +15V DC 0.666A
Connector: 2.5mm type with the center conductor as positive
Power input: 15VDC 0.075A Connector: 2.5mm type with the center conductor as positive
Color: Front: Black anodized Rear: Red clear powder coat
Size and weight:
- Chassis: 6.75"H × 1.4"D × 3.5"W, 16 ounces
- Power supply: 2.2"H × 1.0"D × 1.9"W, 5 ounces