Product Description
Aviom Mix320-D Personal Mixing System with Dante Interface
Features
The Mix320-D Personal Mixing System has been designed specifically for use with Dante™ enabled mixing consoles and networks. It includes everything you need to create a personal mixing system for six performers.
The A320 Personal Mixers get their digital data and power over the same cable, so all you need to do is connect a Cat-5 cable and you're ready to start using the system.
A complete monitoring system in a box, ready to use!
The Mix320-D Personal Mixing System is available in two versions. The standard version is great if you already have in-ear monitors and /or headphones. If you're new to personal mixing and need IEMs, there is an enhanced version of the kit with six MEE Audio M6 Pro in-ear monitors included. These single-driver IEMs include a 72-inch cable, an assortment of ear tips, and a case.
Product Details
The Mix320-D Personal Mixing System makes it easy to add Aviom monitoring to a Dante-enabled mixing console or audio network. No analog input module or console card is required; inputs get patched directly from your Dante network.
The Mix320-D system includes a D400-Dante A-Net Distributor that allows up to 32 channels to be patched from the Dante network to the personal mixing system inputs. The D400-Dante is also used to supply A-Net digital data and DC power to the mixers. The Mix320-D system includes six A320 Personal Mixer for the performers, plus six MT-1a Mic Stand Mounts for attaching the A320 mixers to mic stands, as well as all the Cat-5e cables you'll need to connect the products.
Intuitive Mixing
The A320 Personal Mixer gives performing and recording musicians simple, intuitive control over their monitor mixes. It features a 32-channel mix engine with 16 mono or stereo mix channels buttons and easy to use Stereo Placement controls.
Connect headphones, ear buds, or a wireless in-ear monitoring system to the Personal Mixer and you're ready to start mixing.
Distribute Power and Audio Over Cat-5
For distributing the A-Net digital data and DC power to the A320 Personal Mixers, the system includes the D400-Dante A-Net Distributor.
The D400-Dante also serves as the system's input device; it allows up to 32 channels from your Dante network to be assigned to the eight powered A-Net ports on its front panel. Stereo Link switches allow adjacent channels to be treated as a stereo pairs on the A320 Personal Mixers where they will appear on a single mix channel button.
System Options
The Mix320-D system uses a Dante network for its inputs. If you use a digital console, check out the Mix320-Y Personal Mixing System which includes a Y1 card for Yamaha® consoles for its inputs. Or, if you have an analog console or recording system, the Mix320-A Personal Mixing System is what you need. It includes the 16-channel, line-level AN-16/i Input Module as its front end.
The mixing system packages are also easy to expand when you're ready—just add more Personal Mixers and A-Net Distributors as needed.
Mix320-D Technical Specifications
A320 Specifications
| Audio Output | 1/4" TRS stereo, headphone or line level |
|---|---|
| Stereo Mix Output, Headphone/Line | Tip: Audio Left; Ring: Audio Right; Sleeve: Ground |
| A-Net I/O | 1 A-Net In, RJ45 connector; Supports Pro16 and Pro16e |
| D/A Conversion | 44.1/48kHz, 24-bit |
| Stereo Operation | Stereo Link, per channel pair; Set at the input module; Variable pan per mono channel or pan/spread per stereo channel pair |
| Headphone Output | 275 mW per side into 50 Ohms (both sides driven) |
| Output Impedance | 5 Ohms |
| Freq. Response | 3Hz-22kHz +0.2dB/-3dB at 50 Ohms |
| THD +N | < 0.003% |
| Output Voltage for Personal Mixers | 24VDC, 0.5 amp Transmitted over the Cat-5e cable |
| Signal to Noise (unweighted) |
-106dB (measured with zero data into all channels) |
| Latency | 0.880 msec (measured from analog input to analog output) |
| Pro16e A-Net | Use Cat-5e (or better) cable; Maximum 400 ft (122 m) between devices; Supports Power Over A-Net |
| Cat-5 cable | Use shielded Cat-5e (or better) cable to stay below the CISPR 22 Class B, ICES-003, and FCC 47 CFR Part 15 Class B emissions limits. |
| Power | 24 VDC, 0.5 amp; Power is supplied over the Cat-5 cable when connected to an Aviom A-Net Distributor |
| Dimensions | 10.26" (260.6 mm) wide x 6.14" (155.95 mm) deep x 1.91" (48.51 mm) high |
| Weight | 1.3 lb. (0.59 kg) |
| Options | MT-1a Mic Stand Mount |
D400-Dante Specifications
| Dante Interface | 32 channels (44.1/48kHz Sample Rate) |
|---|---|
| Dante Primary I/O | RJ45 connector |
| Dante Secondary I/O | RJ45 connector |
| Dante LEDs | Network Activity (green); 1GB Network Connection Active (yellow) |
| A-Net Out to Personal Mixers | Eight RJ45 connectors, powered |
| A-Net Out | Pro16e A-Net; RJ45 connector, unpowered |
| LEDs | Power On (red); Network Sync (green) |
| Stereo Link | Two 8-position DIP switch blocks (1-16, 17-32) |
| Output Voltage for Personal Mixers | 24VDC, 0.5 amp Transmitted over the Cat-5e cable |
| A-Net Cables | Front Panel Connections: Shielded Cat-5e (or better) cable must be used to stay below the CISPR 22 Class B, ICES-003, and FCC 47 CFR Part 15 Class B emissions limits. Unshielded Cat-5e cable may be used on all rear panel connections |
| Power Supply | Internal, IEC connector |
| Input Voltage | 100-120 VAC or 200-240 VAC (with selector switch); 50-60Hz @220 W max |
| AC Fuse Types | 115V range: T2.5AL/250V 230V range: T1.25AL/250V |
| Dimensions | 19" (482.6 mm) wide x 7.386" (187.6 mm) deep; 2U, 3.5" (88.9 mm) high |
| Weight | 12.0 lbs (5.44 kg) |
MT-1a Technical Specifications
| Boxed Weight | 1 lb |
|---|---|
| Boxed Dimensions | 7"w x 5"d x 3"h |
| Dimensions | 6.25" wide at front x 4.5" wide at rear x 3" high |
| Connections | Attaches with three screws to bottom of an A640, A320, A360, A-16II, or A-16CS |
| Connectors | Screw Size: 6-32, 1/4-inch (6.35mm) long screws (includes three) |
L-25 Cat-5e Cable
Features
- Flexible black jacket
- Standard RJ45 connectors
Product Details
The L-25 Cat-5e cable can be used with any Pro16® or Pro64® gear. They feature standard RJ45 connectors on each end that can accept the Neutrik NE8MC EtherCon® connector for heavy duty applications.
Note: Only the Neutrik NE8MC EtherCon cable carrier is acceptable for use with pre-assembled Cat-5 cable assemblies. The NE8MC-1 EtherCon part cannot be used with pre-assembled Cat-5 cables.
L-25 Technical Specifications
| Length | 25 feet/7.6m |
|---|---|
| Connector | RJ45 |
