Product Description
Aviom Mix320-D-MEE Personal Mixing System with Dante Interface, Bundled with MEE Audio M6 Pro Earbuds
Features
- (1) D400-Dante A-Net Distributor
- (6) A320 Personal Mixers
- (6) MT-1a Mic Stand Mounts
- (7) Cat-5e cables
- (6) MEE Audio M6 Pro IEMs
The Mix320-D Personal Mixing System has been designed specifically for use with Dante™ enabled mixing consoles and networks. It includes everything you need to create a personal mixing system for six performers.
The A320 Personal Mixers get their digital data and power over the same cable, so all you need to do is connect a Cat-5 cable and you're ready to start using the system.
A complete monitoring system in a box, ready to use!
The Mix320-D Personal Mixing System is available in two versions. The standard version is great if you already have in-ear monitors and /or headphones. If you're new to personal mixing and need IEMs, there is an enhanced version of the kit with six MEE Audio M6 Pro in-ear monitors included. These single-driver IEMs include a 72-inch cable, an assortment of ear tips, and a case.
Product Details
The Mix320-D Personal Mixing System makes it easy to add Aviom monitoring to a Dante-enabled mixing console or audio network. No analog input module or console card is required; inputs get patched directly from your Dante network.
The Mix320-D system includes a D400-Dante A-Net Distributor that allows up to 32 channels to be patched from the Dante network to the personal mixing system inputs. The D400-Dante is also used to supply A-Net digital data and DC power to the mixers. The Mix320-D system includes six A320 Personal Mixer for the performers, plus six MT-1a Mic Stand Mounts for attaching the A320 mixers to mic stands, as well as all the Cat-5e cables you'll need to connect the products.
Intuitive Mixing
The A320 Personal Mixer gives performing and recording musicians simple, intuitive control over their monitor mixes. It features a 32-channel mix engine with 16 mono or stereo mix channels buttons and easy to use Stereo Placement controls.
Connect headphones, ear buds, or a wireless in-ear monitoring system to the Personal Mixer and you're ready to start mixing.
Distribute Power and Audio Over Cat-5
For distributing the A-Net digital data and DC power to the A320 Personal Mixers, the system includes the D400-Dante A-Net Distributor.
The D400-Dante also serves as the system's input device; it allows up to 32 channels from your Dante network to be assigned to the eight powered A-Net ports on its front panel. Stereo Link switches allow adjacent channels to be treated as a stereo pairs on the A320 Personal Mixers where they will appear on a single mix channel button.
In-Ears Included
The enhanced version of the Mix320-D system includes six MEE Audio M6 Pro IEMs. The earbuds feature detachable, replaceable cords and come with an assortment of flexible ear tips that reduce outside noise and allow you to easily find the most comfortable fit for your ears. Each IEM set also includes custom-engraved metal faceplates and a protective case.
System Options
The Mix320-D system uses a Dante network for its inputs. If you use a digital console, check out the Mix320-Y Personal Mixing System which includes a Y1 card for Yamaha® consoles for its inputs. Or, if you have an analog console or recording system, the Mix320-A Personal Mixing System is what you need. It includes the 16-channel, line-level AN-16/i Input Module as its front end.
The mixing system packages are also easy to expand when you're ready—just add more Personal Mixers and A-Net Distributors as needed.
Mix320-D Technical Specifications
A320 Specifications
Audio Output | 1/4" TRS stereo, headphone or line level |
---|---|
Stereo Mix Output, Headphone/Line | Tip: Audio Left; Ring: Audio Right; Sleeve: Ground |
A-Net I/O | 1 A-Net In, RJ45 connector; Supports Pro16 and Pro16e |
D/A Conversion | 44.1/48kHz, 24-bit |
Stereo Operation | Stereo Link, per channel pair; Set at the input module; Variable pan per mono channel or pan/spread per stereo channel pair |
Headphone Output | 275 mW per side into 50 Ohms (both sides driven) |
Output Impedance | 5 Ohms |
Freq. Response | 3Hz-22kHz +0.2dB/-3dB at 50 Ohms |
THD +N | < 0.003% |
Output Voltage for Personal Mixers | 24VDC, 0.5 amp Transmitted over the Cat-5e cable |
Signal to Noise (unweighted) |
-106dB (measured with zero data into all channels) |
Latency | 0.880 msec (measured from analog input to analog output) |
Pro16e A-Net | Use Cat-5e (or better) cable; Maximum 400 ft (122 m) between devices; Supports Power Over A-Net |
Cat-5 cable | Use shielded Cat-5e (or better) cable to stay below the CISPR 22 Class B, ICES-003, and FCC 47 CFR Part 15 Class B emissions limits. |
Power | 24 VDC, 0.5 amp; Power is supplied over the Cat-5 cable when connected to an Aviom A-Net Distributor |
Dimensions | 10.26" (260.6 mm) wide x 6.14" (155.95 mm) deep x 1.91" (48.51 mm) high |
Weight | 1.3 lb. (0.59 kg) |
Options | MT-1a Mic Stand Mount |
D400-Dante Specifications
Dante Interface | 32 channels (44.1/48kHz Sample Rate) |
---|---|
Dante Primary I/O | RJ45 connector |
Dante Secondary I/O | RJ45 connector |
Dante LEDs | Network Activity (green); 1GB Network Connection Active (yellow) |
A-Net Out to Personal Mixers | Eight RJ45 connectors, powered |
A-Net Out | Pro16e A-Net; RJ45 connector, unpowered |
LEDs | Power On (red); Network Sync (green) |
Stereo Link | Two 8-position DIP switch blocks (1-16, 17-32) |
Output Voltage for Personal Mixers | 24VDC, 0.5 amp Transmitted over the Cat-5e cable |
A-Net Cables | Front Panel Connections: Shielded Cat-5e (or better) cable must be used to stay below the CISPR 22 Class B, ICES-003, and FCC 47 CFR Part 15 Class B emissions limits. Unshielded Cat-5e cable may be used on all rear panel connections |
Power Supply | Internal, IEC connector |
Input Voltage | 100-120 VAC or 200-240 VAC (with selector switch); 50-60Hz @220 W max |
AC Fuse Types | 115V range: T2.5AL/250V 230V range: T1.25AL/250V |
Dimensions | 19" (482.6 mm) wide x 7.386" (187.6 mm) deep; 2U, 3.5" (88.9 mm) high |
Weight | 12.0 lbs (5.44 kg) |
MT-1a Technical Specifications
Boxed Weight | 1 lb |
---|---|
Boxed Dimensions | 7"w x 5"d x 3"h |
Dimensions | 6.25" wide at front x 4.5" wide at rear x 3" high |
Connections | Attaches with three screws to bottom of an A640, A320, A360, A-16II, or A-16CS |
Connectors | Screw Size: 6-32, 1/4-inch (6.35mm) long screws (includes three) |
L-25 Cat-5e Cable
Features
- Flexible black jacket
- Standard RJ45 connectors
Product Details
The L-25 Cat-5e cable can be used with any Pro16® or Pro64® gear. They feature standard RJ45 connectors on each end that can accept the Neutrik NE8MC EtherCon® connector for heavy duty applications.
Note: Only the Neutrik NE8MC EtherCon cable carrier is acceptable for use with pre-assembled Cat-5 cable assemblies. The NE8MC-1 EtherCon part cannot be used with pre-assembled Cat-5 cables.
L-25 Technical Specifications
Length | 25 feet/7.6m |
---|---|
Connector | RJ45 |